Archive for April, 2013

Our Retail store has a Spring Deck Special

Tuesday, April 30th, 2013

We have a Spring Deck Products Special for our customers.  The Special consists of all the products and tools a person will need to freshen up their deck for the summer season.  Check it out and refer it to your friends.  It’s a good program that will help out our customers.

Restore-x Wood deck finishes

Restore-X® Exterior Wood Brightener – Part 3

Wednesday, April 17th, 2013

Restore-X® Exterior Wood Brightener is a citrus based product that brightens the wood grain appearance to bring out the brilliance of the wood and its grain features.  Exterior Wood Brightener is an excellent product that can be used as a stand-alone or as step #2 after the Deck Cleaner or EFR.  Exterior Wood Brightener is available in a liquid or a 6 oz. package concentrate that makes 1 gallon.


1. READ LABEL DIRECTIONS ON ALL CONTAINERS CAREFULLY and note specific instructions for Restore-X® EFR, Deck Cleaner and Wood Brightener contained in this guide.

2. Conduct several small test samples in inconspicuous areas (one foot square).  It is essential to conduct several tests in different areas, as the condition of the surface will vary depending on the extent of exposure to the elements.  Monitor the time it takes and the amount of product used to achieve satisfactory results.  This test sample will help you bid the job accurately and schedule the amount of time necessary to complete the project.

3. Materials and equipment: Having the proper materials and equipment available before applying Restore-X® will help ensure the success of your project.  Your experience will bear this out.  The following items are highly recommended:

· Rubber Gloves and Boots

· Eye Protection (goggles)

· High-Pressure Washer, Hoses, etc.

· Duct Tape and Plastic (to protect aluminum)

· Synthetic Rollers and Brushes only

· All Stainless Steel Airless Sprayer

· Sprayer for Deck Cleaner or Wood Brightener (pump-up garden Type)

· Respirators (only if Restore-X® is sprayed)

Sprayer Equipment: Airless spray equipment is recommended for Deck Cleaner and Wood Brightener.  All Internal sprayer parts (fluid section) must be stainless steel, Teflon, plastic, or nylon. DO NOT USE Restore-X® in spray equipment (fluid section) with aluminum alloy or leather internal parts or packings.  CAUTION: Do not pump Restore-X® through old paint lines!  Residual paint remaining in the hose will be sloughed off and will clog the spray tip.

4. Take care of the landscape.  Rinse shrubs and surrounding lawn before and after treatment.

5. Preparing the surfaces.  Mask all aluminum windows and door frames securely with silver duct tape and plastic (or other non-porous leak-resistant tape).  This is important as Restore-X® will remove anodizing from metals and discolor aluminum.  If Restore-X® does come in contact, rinse immediately and thoroughly with water.  If damage does occur, contact the window/door frame manufacturer.  Use with extreme caution on doors.  Water may seep through paneled doors staining interior surfaces.  With hardwood doors, water may cause both darkening and a raising of the grain.

6. Application: Before applying Restore-X®, thoroughly wet the surface and broom off excess water.  This encourages even penetration of the product.  Three important steps to remember when applying Restore-X®: 1) apply a heavy coat using only synthetic brushes or rollers, 2) keep the surface from drying by misting with water* if necessary, and 3) wait for the product to do the job.

*An alternate method for keeping the surface damp:  After application of Restore-X®, use 1 mil plastic sheeting to cover the surface.  Place plastic against product; plastic will stay in place, reduce moisture evaporation and speed removal.

7. WAIT!

EFR: It is very important to allow Restore-X® time to dissolve the deteriorated finish and weathered wood.  Latex paints may take considerably longer than oil base paints; so do expect some variation in removal time.  Take a break while Restore-X® works for you, and then test several areas with a stiff brush and water.  If the results are satisfactory, proceed with removal.  Typically, removal times vary from 1-4 hours.  If a second coat is required, wash away the first coat and reapply.  Note:  If re-coating with paint or a solid-body stain, complete removal of weathered paint or stain may not be necessary.  Any remaining stain or paint may provide a good substrate for adhesion.  You will need to test the remaining paint or stain to determine if it is suitable for re-coating.

Deck Cleaner: Unfinished weathered wood will take 1 to 15 minutes.  Deteriorated stain in exposed areas removes in as little as 5 minutes.  Stain in protected areas may require up to 1 hour.  Expect some variation in the time required.  Mist lightly with water every 15-20 minutes.

Wood Brightener:  All wood should be clean before using Wood Brightener.  Pressure wash surface or use EFR or Deck Cleaner before using Wood Brightener.  All applications should be left to work 5-15 minutes.  If first application leaves an uneven finish or does not brighten to your desired finish, simply reapply.

8. Removal: For large projects, a pressure washer will greatly increase productivity.  Remember, however, that a pressure washer can do damage when used improperly.  Be careful not to place the nozzle too close to bare wood or windows.  Use a fan tip that will not “drill” the surface.  Rinse the surface thoroughly, but do not overwork stubborn finishes with the pressure washer, as damage to surrounding exposed surfaces may result.  Rather, simply spot apply Restore-X® and repeat the procedure.  Remember, it is not necessary to achieve 100% removal during surface preparation.  Paint that still maintains a good bond with the underlying material can provide a satisfactory surface for repainting or staining with a solid-body stain.  If a pressure washer is not at your disposal, be sure to agitate the surface in one direction (with the grain) to promote removal of stains or weathered wood.  Do not “scrub back and forth”.  Because Restore-X® is removing old deteriorated wood cells, it can cause tiny “hairs” to develop on the surface.  Scrubbing back and forth can magnify this effect.  Too much of this can require sanding, which defeats the purpose of this product. Agitating in one direction with the grain will help to keep these “hairs” from exposing themselves.

9. Refinish the Surface: To ensure a lasting natural wood color, always complete the Restore-X® process by applying a clear finish, wood preservative or semi-transparent stain as soon as possible.  Time is less important when repainting, but avoid long delays that may allow dirt and/or mildew deposits.  Contact your Restore-X® Dealer about 02C Series Penetrating Wood Finishes.

Restore-X® Exterior Wood Deck Cleaner

Tuesday, April 2nd, 2013

Part 2:

Restore-X® Exterior Wood Deck Cleaner is the first step in restoring the beauty of exterior unfinished and semi-transparent stained woods that are weathered and have dirt deposits or stains.  Now it is possible to remove old semi-transparent stain that has lost its original appearance.  Restore-X® Deck Cleaner dissolves old stain and accompanying watermarks and eliminates the graying effects of weathering by removing the deteriorated wood cells, mildew, pollutants, etc., that cause discoloration.  Old wood looks new again and unsightly semi-transparent stain is easily removed.  No longer is it necessary to cover up with solid stain or paint.  Restore-X® Deck Cleaner is the answer for decks, wood siding, fences, benches, planters, patio furniture, and other exterior wood surfaces.


The following estimates are intended as a general guideline only.

Finish Average Waiting Time

Weathered Wood                                  1-15 min.

Semi-Transparent Oil Wood Stain      5-45 min.

Semi-Transparent Latex Wood Stain  5-60 min.